How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
Have you been searching for help and advice concerning How to Install a Bathtub Yourself?
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is readily accessible, the job can move speedily; if you need to open up a wall to get rid of the old bathtub and place the brand-new tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the new one. See to it you have actually qualified on your own for the task and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to consider using one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This post will assist you install a brand-new bathtub in your shower room if you have actually already acquired a new bathtub as well as do not need to transform the arrangement of your previous water pipes.
Your devices and material list ought to consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in location between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the needed position. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the tub until the level reads level.
To mount taps, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the supply of water and also inspect all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been made use of at least once as this will certainly settle it into its last position.
Preparing for the Setup
First of all, the sustaining structure provided with the bath should be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to prevent strain on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, causing issues with moisture as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to enable the movement experienced when the tub remains in usage. The sealant can break fairly very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that write-up on Installing A Bathtub from someone on another web blog. So long as you enjoyed reading our blog post please make sure you remember to pass it around. We take joy in reading our article about Installing A Bathtub.
Start Now Report this page